ISO 8434-2 PDF

ISO INTERNATIONAL. STANDARD. ISO. Second edition. Metallic tube connections for fluid power and general use —. Part 2. 37° flare couplings to ISO comprise a body. (1), pressure sleeve (2) and securing nut (3). By exchanging the pressure sleeve, the same coupling can be. The SAE J/ISO standard outlines the general and dimensional requirements for the design and performance of 37° flaring fittings, suitable to be used.

Author: Tauk Morisar
Country: Iceland
Language: English (Spanish)
Genre: Photos
Published (Last): 25 July 2010
Pages: 185
PDF File Size: 3.40 Mb
ePub File Size: 14.45 Mb
ISBN: 650-6-80485-345-3
Downloads: 66129
Price: Free* [*Free Regsitration Required]
Uploader: Kagajinn

As a member isso. Some of the tests described in this part of ISO are considered hazardous. Use the same procedures as in 5. Dimensions list any exceptions: Stud ends with metal-to-metal sealing type B. The distance between the centrelines of test ports shall be a minimum of 1,5 times the port diameter. This report is based on accounts to which one of the following applies:.

Major international companies that have used these connectors have adopted the design without noting any problems. Fitting and stud end standards 1. Seals shall conform to their respective dimensional requirements, and O-rings shall meet or exceed the quality requirements for grade N general purpose of ISOif applicable. The threads are integral to themselves, connectors of this type match only to themselves and, other than having metric threads, no value in changing could be found.

Testing of six samples to confirm that they are capable of withstanding the overtorque qualification test when tested to the overtorque values shown in their respective standards. Cold-reduced carbon steel sheet of commercial All components tested shall be tested in the final form as the customer receives the partincluding annealing as required for brazing. Reference number ISO Quality management systems —. Components may be connected through their ports by connections connectorstubes and hoses.

  HP ZR24W MANUAL PDF

Heavy-duty S series and light-duty L series stud ends with elastomeric sealing type E. Profile of Global Survey Sample.

Also, the isso overtorque and seal performance 84344-2 been extensively tested; to change to metric threads would require an extensive test program at considerable cost without providing any functional improvement.

Adjustable stud torques shall be applied after being backed out one full turn from finger- tight position to test correctly the worst possible actual assembly conditions. Test methods for threaded hydraulic fluid power connections Reference number ISO The distance between the port centreline and the edge of the test block shall be a minimum of 1 times the port diameter.

ISO – SAI Global –

AS Composts, soil conditioners and mulches Verification and calibration of testing. The cycle ixo shall be uniform at 0,5 Hz to 1,3 Hz and shall conform to the wave pattern shown in ISO The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO Use the lubricant specified in 5.

Your consent to our cookies if you continue to use this website. Use the same equipment as specified in 5.

  LIVRO ESCOTISMO PARA RAPAZES EM PDF

It is therefore essential that, in conducting these tests, all appropriate safety precautions are strictly adhered to.

Connections shall be restrained during the test uso the wrench shall be located at the threaded end of the nut hex. Metallic tube connections for fluid power. Test results and test conditions oso be reported on the test data form given in annex A. Testing of two samples to confirm that they are capable of withstanding a vacuum of 6,5 kPa 0, bar absolute pressure for 5 min without leakage.

Adobe is a trademark of Adobe Systems Incorporated.

BS ISO 8434-2:2007

Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by. One of their six values Every care has been taken to ensure that the file is suitable for use by ISO member bodies. Testing of three samples to confirm that the specified connection s is are capable of withstanding a minimum of four times the working pressure without failure.

COM To ensure the functioning of the site, we use cookies. This is a free 6 page sample. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Components must be designed to meet these requirements under varying conditions. In accordance with Adobe’s licensing policy, this file may be printed or